P0299 means your turbo isn’t giving the engine the boost it asked for. Your car noticed the shortfall, stored the code, and probably cut your power to protect itself. On a VW-group car you might see it written as P029900, or in VCDS as 16683 / 000665.
You can drive it, gently. Limp mode caps your power but doesn’t stop the car. Don’t push it hard, and don’t leave it for weeks.
The good news: it’s rarely the turbo. On a petrol TSI or TFSI it’s usually a torn diverter valve or a split hose letting the boost escape. On a TDI it’s usually the lower intercooler hose, or the turbo’s vanes sticking with soot, which is one of the common 2.0 TDI problems rather than a turbo failure. All of those cost a fraction of a turbo, and this page shows you how to find which one you have before anyone quotes for a new one.
Is It Safe To Drive With A P0299 Code?
Yes, carefully, and not for long. Limp mode caps the boost, so you lose most of your power above about 2,500 rpm, and an ignition cycle usually brings it back until the fault trips again, which is why owners live with this for months. Don’t: a boost leak makes the engine run rich, which loads a diesel’s DPF faster, and sticking vanes only get worse.
Stop driving if the code comes with blue or white smoke, a loud whine or grinding from the turbo, oil in the intercooler pipes, or an oil pressure light. Those point at the turbo itself, and driving on can put it through the engine.
What P0299 Fault Code Means on a VW-Group Car
When your car stores this code, it also saves a note of what was happening at that second: how fast the engine was turning, how fast you were going, and how much boost the turbo was asked for against how much it actually made. Your scanner shows it with the fault. Read it first, because it tells you when the problem shows up.
Here’s a real one posted by a 2.0 TDI owner: motorway speed, engine pulling hard, boost asked for 2,130 mbar and only 1,534 mbar delivered. The turbo was told to make about 1.1 bar and managed half of it.
Look at your own the same way. Those two boost numbers are the whole problem in figures, what the car wanted and what it got. If it happened at speed with the engine warm and working, you’re looking for a leak or a boost control fault, and that’s the usual answer. If it happened at low speed or just after a cold start, a sticking turbo on a diesel moves up the list. One more thing to check: the fault frequency. A 1 means it’s happened once. A 4 means it keeps happening, so it’s a real fault and not a one-off.
Symptoms of P0299 Fault Code
- Loss of power above about 2,500 rpm: normal at low revs, flat when you ask for more.
- Limp mode until you switch off and on. Engine light on.
- A hiss or whistle under acceleration, or a whoosh when you lift off on a petrol.
- Black smoke under load on a diesel.
- The code comes back after clearing, the next time you ask for full boost.
One clue before you test: only under full load means a leak or a wastegate; after idling or short trips on a TDI means sticking vanes; comes and goes means a diverter valve or a small leak; a whine, smoke or oil in the pipes means the turbo. Anything else, the code stored with it decides.
How to Diagnose a P0299 Code
1. Read the freeze frame
Your scanner stores the engine speed, road speed and the boost asked for against the boost delivered at the moment the code set. Read it before you clear anything. A real one from a 2.0 TDI: motorway speed, 2,130 mbar asked for, 1,534 delivered, so the turbo made half of what it was told to.
If it happened at speed with the engine warm, it is a leak or a boost control fault, which is the usual answer. If it happened at low speed or just after a cold start, sticking vanes on a diesel move up the list. A fault frequency of 1 is a one-off; 4 or more is a real fault.
2. Log specified against actual boost
Any scanner that reads VW-group data shows “charge pressure specified” and “charge pressure actual”. Hold steady throttle in third gear and watch both. A healthy engine keeps them within a few hundred mbar. A gap that opens as load rises is a leak or a wastegate. A gap at all loads is a sensor or a control fault.
3. Find the leak
With the engine running, squeeze every hose between the turbo and the throttle body and check every clip. On a TDI start at the lower intercooler hose: it sits lowest, collects oil and splits first.
If nothing shows, have the system pressure-tested. A garage caps the turbo inlet, applies a few psi, and leaks hiss. It costs about £30 and it is the test that saves a £1,000 turbo. If it comes back clean and boost still cannot reach target, work the fix steps below, cheapest first.
P0299 Causes
Petrol (1.4, 1.8, 2.0 TSI, 2.0 TFSI)
- Torn diverter valve (N249)
- Boost leak: split hose, loose clip, cracked charge pipe
- Wastegate actuator play
- PCV / oil separator diaphragm
- Charge pressure or MAP sensor
- Restricted catalyst
Diesel (1.6, 1.9, 2.0 TDI)
- Boost leak, usually the lower intercooler hose or its clip
- Sticking VNT vanes
- N75 solenoid or its vacuum hoses
- Electronic turbo actuator (CR-TDI)
- Seized exhaust flap module (J883)
- Blocked DPF or EGR stuck open
- Worn turbo
Documented P0299 Faults by Model
These are the faults VW and Audi have published for specific engines, with the part numbers. If your car is here, start here.
- Audi A3, A4 and A4 Cabriolet, 2005 to 2007, 2.0 TFSI. Audi’s bulletin 2013060: the recirculation valve N249. Pull it off the turbo and look at the rubber membrane; torn means replace. Part 06F145710G.
- Audi A4, A5, A5 Cabriolet and Q5, 2009 to 2012, CAEB engine. Audi’s bulletin 2031245: worn wastegate linkage lets the flap sit loose and boost escapes. If the flap has play, the repair is a new turbo with clip 06J145220B; Audi says the clip must not go on a used turbo.
- All 2008 to 2015 VWs with the 2.0 TSI (CCTA, CBFA). VW’s Tech Tip 21-10-02: a roll pin backs out and the wastegate lever drops and seizes, giving underboost or overboost, sometimes intermittently. Check for 3 mm of clearance under the lever; none means a new turbo.
- Jetta 2009 (CBEA), and Golf, Jetta and SportWagen 2010 to 2014 (CJAA), 2.0 TDI. VW’s bulletin 2026771 gives the order: vacuum hoses kinked or twisted, the stud and clamp nut on the turbo broken or missing, the vacuum diaphragm, the plastic boost pipe to the intercooler, the hose seals at the intercooler, then ECM software. Test the diaphragm with a hand pump at about 600 mbar; if it won’t hold, fit the G581 diaphragm, part 03L198716A. VW says not to replace the turbo for a failed G581. Also check the exhaust flap module (J883) isn’t seized.
- Passat 2012 to 2014, 2.0 TDI (CKRA). VW’s bulletin covers a broken or seized turbine shaft, with a revised oil supply pipe in the repair. The one model where the turbo really can be the answer.
- Polo, Fabia, Ibiza and Golf with the 1.0 to 1.4 TSI. A failed diverter valve or a loose charge-pipe clip. These turbos are wastegated, so sticking vanes aren’t on the list. On the 1.0 TSI, the electric wastegate actuator sticking is the documented pattern; the 1.0 TSI problems page covers it. On the 1.5 TSI 150 it is the actuator rod rattling loose and leaking boost, which is the 1.5 TSI’s actuator rattle on its page.
- Caddy, Transporter, Crafter and Amarok, 1.9 to 2.5 TDI. same causes as any TDI, but the leak is usually at a joint under the van you cannot see, so pressure-test rather than look. On the 1.9 TDI-PD (BLS), check the vacuum reservoir in the valve cover first.
Codes Stored With P0299
Most cars with this code have more than one. The second code usually tells you which system to fix first.
- P0234, overboost. The opposite problem, same control system. Both codes together mean the boost control can’t regulate either way: vanes or the N75 on a diesel, the wastegate actuator on a petrol.
- P2563, turbo actuator position. The actuator’s own sensor says the vanes or wastegate aren’t where the ECU asked, so the underboost is a consequence. Fix DTC P2563 first; on a VAG diesel it’s usually the actuator diaphragm or a vacuum leak, not the turbo.
- P2279, intake air system leak. Air is getting in after the air mass meter on the same pressure side: a charge pipe, the intercooler or, on a TSI, the breather valve passing boost into the crankcase. Fix DTC P2279 first and the underboost usually goes with it.
- P2002, P2463, P2458, or the DPF light. The exhaust is blocked and the turbo can’t spin against it. Fix the DPF first, and the P0299 usually goes with it.
- P0401, EGR flow insufficient. Common on a diesel, and the two often store together. A sooted EGR and sticking turbo vanes come from the same short-trip driving.
- P0300 to P0304, misfires, or fuel-trim codes. On a TSI this points at the PCV, not the turbo.
- P0101 or P0102, mass air flow. Air is leaking in after the MAF. The leak is the fault, not the sensor.
- P0235, P0236 or P0238, boost sensor circuit. Now the sensor is a real suspect, which it isn’t when P0299 is stored on its own.
How Do You Fix a P0299 Code?
Work the steps in order and stop at the first one that finds the fault.
Petrol (TSI and TFSI)
- Check the diverter valve. Pull it off the turbo and look at the rubber diaphragm. If it is torn, fit the revised valve for your engine code (06F145710G on the 2005 to 2007 2.0 TFSI). Three T30 bolts.
- Find the boost leak. Squeeze every hose between the turbo and the throttle body, check every clip, look for a cracked charge pipe. Replace the hose, clip or pipe, with fresh O-rings on the 2.0 TSI. If nothing shows, have the system pressure-tested.
- Check the wastegate lever for play on the 2.0 TSI and 2.0 TFSI. Play, or a lever that has dropped, means a replacement turbo; the bulletins below say which engines.
- Replace the PCV or oil separator if its diaphragm has split. A hiss from the valve at idle is the usual sign. Fit the current revision.
- Test the charge pressure sensor. Engine off, it should read about 1,000 mbar. Check the connector and wiring before replacing it.
- If everything above is clean, have the catalyst checked for a restriction.
Diesel (TDI)
- Only then the turbo. Replace it, flush the oil feed and return lines, fit new oil and a filter, and prime it before the first start.
- Replace the lower intercooler hose and its clip if the hose is split, soft or has popped off. The undertray comes off.
- Free the vanes. Blip the throttle and watch the actuator rod: no movement, or movement in steps, means they are sticking. Free the arm by hand, then an on-car clean through the actuator side, or the turbo off for a proper one.
- Test the vacuum side. Put a hand vacuum pump on the actuator diaphragm and pull about 600 mbar. If it does not hold, replace the diaphragm (G581 on the CBEA and CJAA, part 03L198716A). If it holds, replace the kinked hoses or the N75 valve.
- On a common-rail TDI with an electronic actuator, replace the actuator and adapt it to the turbo with VCDS or OBDeleven PRO.
- Free or replace a seized exhaust flap module (J883).
- If a DPF or EGR code is stored with it, force a regeneration and clean or replace the part. The P0299 usually goes with it.
How to confirm the fix
After the fix, clear the code, drive a full cycle with one sustained full-throttle pull, and log specified against actual boost. If the two lines separate again, there is a second fault; a boost leak often hides a smaller one behind it. Don’t clear the code before the fix, so the freeze frame is still there if it comes back. On a diesel, one sustained full-throttle pull a week keeps the vanes moving.
DIY or Garage?
Every home job above needs hand tools, T30 and T25 Torx bits, and a scanner that shows charge pressure specified and actual. A £30 Bluetooth adapter with a VAG-capable app does that; a generic code reader shows the code and not the boost figures you need to confirm the fix. Ramps help on a TDI, because the lower intercooler hose is under the car.
A garage is for the pressure or smoke test if your own look finds nothing (£30 to £60, and the most useful thing anyone can do on this code, so ask for it by name), for anything that needs the turbo off or a tool with write access, and for DPF and EGR work. A diagnosis is half an hour to an hour of labour, £40 to £90 in the UK, and most garages credit it against the repair if you have the work done there.
P0299 Fault Code After a Remap
A Stage 1 map raises the boost the ECU asks for. A clip that held at stock boost, a tired diverter valve or an actuator that could just reach the old target can all fail at the new one, and P0299 arrives a few weeks after the remap. Any remapped car has less margin than a stock one, because the map asks for more.
Do the same checks in the same order. If they’re all clean, the map is asking for more than the hardware can deliver, and the tuner needs to log the car and lower the targets. Flashing back to stock for a week is a fair test: if the code disappears at stock boost, the hardware is marginal and the map is showing it up, not causing it.
Before You Pay for a Turbo
If a garage says the turbo has failed, ask for two things: the pressure-test result and a log of specified against actual boost. A worn turbo shows in both. A leak shows in the pressure test and not in shaft play, and a sticking vane mechanism shows as boost that reaches target sometimes and not others.
If they can’t show you either, you’re being asked to pay four figures for a guess. Getting a second opinion costs another diagnosis fee and can save you a turbo.
How Much Does It Cost To Fix a P0299 Code?
Fitted at an independent garage, September 2026. UK turbo figures are WhoCanFixMyCar’s average of £1,126 (£1,073 for a Volkswagen, £1,146 for an Audi); US figures are RepairPal’s estimates.
| Repair | UK | US |
|---|---|---|
| Intercooler hose or clip | £60 to £180 | $280 to $700 |
| Diverter valve (TSI/TFSI) | £80 to £150 | $150 to $350 |
| N75 valve or vacuum hoses | £80 to £180 | $150 to $350 |
| PCV / oil separator (TSI) | £150 to £300 | $300 to $600 |
| Charge pressure sensor | £60 to £130 | $120 to $280 |
| Turbo actuator, or on-car vane clean | £200 to £450 | $400 to $900 |
| Replacement turbo | £900 to £1,800 | $1,600 to $3,300 |
Most P0299 repairs sit in the top four rows. The turbo row is where you end up when nobody pressure-tested the system first.
FAQs
A boost leak on a diesel and a torn diverter valve on a TSI or TFSI petrol. Both are cheap parts; both are found with a pressure test.
Yes. A restricted exhaust stops the turbine spinning up, and VW lists a restricted exhaust as a cause. If the DPF light or P2002 / P2463 is on as well, fix the DPF before you touch the turbo.
It can, but it usually sets its own code first. Check what the sensor reads with the engine off before you replace it.
The limp mode clears with an ignition cycle. The code stays stored until the fault is fixed or the memory is cleared, and it comes back the next time the turbo is asked for full boost.
The engine management light on is an MOT fail in the UK. Fix the cause, clear the code, and complete a drive cycle before the test.
Last Updated: November 2026

Founder of TheCarLane | Automotive Enthusiast
Ayush shares practical automotive knowledge based on real-world ownership and hands-on experience. His work focuses on diagnostics, engine systems, common car problems, and clear explanations that help everyday drivers understand their vehicles better.

